首 页文档资料下载资料维修视频包年699元
请登录  |  免费注册
当前位置:精通维修下载 > 文档资料 > 家电技术 > 单元电路介绍 > 电源电路
Power supply +20V/15A and +12V/3A
来源:本站整理  作者:佚名  2010-02-19 15:18:50





The circuit is based on applICation of National SEMIconductor. First is constituted by three voltage regulators LM338 [IC1-2-3] connected `'in parallel' '. The each one regulator has the possibility of giving 5 A in his output. Also exists the possibility to regulate the output voltage from +4.5V until 25V DC, stabilized. The voltage regulation in the output becomes with the TR1. If it does not exist the need of this continuous output voltage regulation, then we CAN measure the resistance value of trimmer TR1 in the particular output voltage and him replace with proportional value constant resistance. The Rectifier Bridge BR1 should be placed in some point of metal box so that it's frozen. On the contrary the IC1-2-3, that good are is TO-3 case, should be placed in a capable dimensions heatsink, with suitably mica isolation between them and the heatsink. Also it should sort-circuit in no point with heatsink. Resistors R1-2-3 should be placed in some distance from the PCB in which make the circuit, because are hot and exists the danger to burn the printed board in that point. A point that should it's given attention they are the cables from where it passes big current, it’s big diameter, as well and the output plug of suitable type and carefully placed so that does not exist the case of short-circuit. In the second part of drawing exists a simpler circuit that is based on the voltage regulator LM350 which has the possibility of giving in the exit regulated voltage from +1.25V until 25V Dc and biggest current 3 A. Good is the IC5 are in case the TO-3 for better thermic conduct and it's placed on heatsink [with essential mica between this and heatsink]. The voltage regulation in the output becomes with the trimmer TR2. All the circuit is supplied from power transformer bigger than 450VA. The manufacture of circuit should become in suitable dimension box that should ventilate well. In the expulsion of temperature can help a fan 12X12cm working in 230Vac. In the outputs you can place Voltmeter and Ambermeter.

R1-2-3=0.1R 5W C3-5-8-10=100nF 100V MKT IC1-2-3=LM338 [TO-3 case] on Heatsink
R4=100R 0.5W C4=220pF 100V ceramic IC4=LM308
R5=150R 0.5W  C6-11=47uF 63V IC5=LM350 [TO-220 or TO-3 case] on Heatsink
R6-8=330R 0.5W C7=4700uF 63V J1=3 terminal bLOCk computer type
R7-9=4K7  0.5W C9=10uF 40V J2-3-4-5=2PIN Connector 3.96mm step pin
R10-13=1K5 0.5W D1-2=LED Red 5mm F1=Fuse 5A slow block
R11-12=220R 0.5W D3=1N4007 T1=230Vac/22Vac 600VA transformer
TR1=1K5 trimmer BR1=Bridge Rectifier >250V 35A on Heatsink

Symbols

TR2=4K7 trimmer BR2=Bridge Rectifier >250V 3A uF=microfarand, R=ohms, K=Kilohms
C-2=10000uF 63V Q1=2N2905

关键词:

·上一文章:12Vdc to 220Vac 50W Converter
·下一文章:简单的1.5V升4.5V电路

文章评论评论内容只代表网友观点,与本站立场无关!

   评论摘要(共 0 条,得分 0 分,平均 0 分)
Copyright © 2007-2017 down.gzweix.Com. All Rights Reserved .
页面执行时间:77,289.06000 毫秒